Posted on

Single Afternoon Loom Knit Slipper Socks

loom knit slipper socks

You can make these comfy, cozy slipper socks in a single afternoon! The really great thing about this easy knitting project is that it’s calming, gives you a chance to catch up on your favorite listening and results in a great handmade gift for a friend!

Even if you’re unfamiliar with loom knitting, you can do this. I would recommend first viewing this video, which will show you in a few minutes the basic e wrap stitch, which is used on the slipper sock from ankle to toe. https://www.youtube.com/watch?v=7DVRbwzQm7A

Supplies you’ll need:

Supplies for loom knit slipper socks
Supplies for loom knit slipper socks

The loom is a small 24 peg that can be used for baby hats and scarves as well. Have to do a shout out about the knitting counter; I could not do this project without it. http://www.clover-usa.com/en/knitting-and-crochet/80-knitting-counter-mini-kacha-kacha.html?search_query=counter&results=2

A few words about yarn. I doubled the lighter weight green yarn used on the cuffs. It more closely follows the medium bulk of the heel and foot. For the toe I went to a lighter yarn and a single strand. The toe, of course, is cinched up and makes the decrease easier with less bulk. All the yarn shown here is washable wool blend, lovely soft. You can use whatever you like, but I find the 100% acrylics not quite so soft a feel.

Onward to the cuff…

Slipper Sock cuff

E wrap a single row, referring to above referenced video if you need. For the next 12 rows, you’ll alternate knit and purl stitches in each row. k,p,k,p,k,p etc. If you’ve not done this on a loom, you’ll work to the right with working yarn in front. The first peg to the right of the anchor will be knit. For the knit stitch the hook reaches under the wrapped loop, and grabs the working yarn from above, gets pulled down and knit off. The next stitch is purled, and the process is reversed. The hook will go behind the loop from the top, reaching down to grab the working yarn. Knit and purl alternately for 12 rows. Leaving a tail five inches or so, cut the cuff working yarn and double knot to ankle/foot yarn.

Slipper sock cuff 12 rows
Slipper sock cuff 12 rows

I would be so lost without my little knitting counter friend!

The ankle is simple and quick…just e wrap knit 5 rows. This usually takes me two or three songs to do.

Inside view of slipper sock ankle
Inside view of slipper sock ankle

The next thing to do is mark the 13th peg. I’ve used a green wire tie here, and this works fine. Now is the time to leave a yarn tail, cut the cuff yarn, and double knot the heel yarn. For the heel, you’ll only be working pegs 1-12, and will e wrap back and forth between them for 4 rows. Always start on adjacent peg, and do knit the last peg.

First part of slipper sock heel
First part of slipper sock heel

To decrease heel and reattach to loom, you’ll leave your (13th peg) marker on and, beginning at the 12th peg, pull that loop onto the adjacent (11th) peg. Go to peg one, wrap (peg 11 as well, even though it will have three loops on it) and work the row, treating the bottom two loops on peg 11 as a single loop. Then go to peg 1, moving it to adjacent peg 2 and following the above instruction until there are three empty pegs per side.

Decrease heel
Decrease heel

To reattach your knitting to the loom, with your hook take a top edge loop of yarn closest to peg that’s holding the ankle knitting and put on that peg (it will eliminate holes). Same thing for remaining six empty pegs. This part can be a bit of a challenge, but take your time to “see” the best way to spread out the heel knitting over the pegs and it will be fine. Also, if there are any holes in the heel/ankle/foot area, those long tails from changing yarn make stitching the hole shut an easy matter.

Once you’ve got your knitting reattached, cut a long tail and switch back to yarn that was used for the ankle. Double knot, and e wrap all round the loom. You’ll now remove that marker from peg 13, and notice that your number one peg is now on peg 4. There will be three loops on a couple of the pegs, treat the bottom two as if they were a single loop.

From here until the toe, knit as many rows as desired. On a medium bulky yarn, I find 22 rows equates to about a womens 7.5. As you approach the end of the foot, make certain the knitting is not too tight. The toe will consist of three additional rows.

When you reach the toe, cut a tail several inches long and tie on the yarn you’ll use for this. Best to use a yarn about half the thickness of the foot yarn. Double knot, and move every other peg onto the adjacent peg to the right. Then “weave” the working yarn in front of the pegs with loops and behind the empties. Not too tight. Then knit the double loops over. Pulling one peg over at a time is easier than both at once.

Decrease toe
Decrease toe

Do the next two rows the very same way, remembering to keep yarn loose for ease.

Leave a tail about one and a half times the loom diameter and thread onto your flexible yarn needle. Go through all loops, and once again through first loop. At this point you can remove knitting from loom and turn inside out to close (drawstring) as well as weave in all tails and stitch any holes that may exist. If you’ve not used this drawstring method, here’s an excellent lesson in doing so http://www.loomahat.com/how-to-loom-knit-a-hat/close/ .

Inside out at finish, ready for weaving in tails
Inside out at finish, ready for weaving in tails

The second sock goes much quicker with the insight from the first one. A bow sewn on the cuff from yarn that’s been braided or spool knit http://bettyrockwear.com/retro-craft-tools-spool-knitter/ would really make for a special handmade gift. Or enjoy them on your own feet!

Finished wool slipper socks!
Finished wool slipper socks!

 

Posted on

How To Make A Simple Slipcover For Round Ottoman Using A T Shirt

If you have a favorite old t shirt (perhaps an old concert t for rock and roll flavor) that you’re unable to part with but are no longer wearing, you can easily fashion it into a casual slipcover for a round ottoman, such as this one:Denim Drum Ottoman 1

 

For this project you’ll need a basic sewing machine, an old t shirt, a round ottoman (although this method will work on an oval shape as well), fabric shears, a marker, piece of fabric for ottoman top plus a couple of inches for seam allowance, thread, pins and a measuring tape. A steam iron is helpful but not necessary.

Slip t shirt over ottoman and decide where the bottom edge will be. You’ll be using the existing hem as the bottom edge. Measure, adding two inches for seam allowance. My ottoman is 11″ and so will be cut to 13″

Measure side width plus seam allowance 2

Lay as flat and evenly as you can on your cutting surface. (It’s helpful to align edges and press first)

Lay side fabric out for cutting 3

Cut at predetermined distance from bottom hem. Mine was 13″

Cut side fabric 4

Set aside the side panel, and lay your top piece face down on your cutting surface. Put the ottoman upside down on this fabric and, using a felt marker lightly draw line around ottoman. (Holding marker parallel to ottoman side makes it easier) This line will serve as your seam guide when attaching top. Measure and mark at several points 2″ out from this line for your seam allowance.

Cut out top piece along those points.                                                 Prepare top cover fabric 5

Moving your attention back to the side panel, measure circumference of ottoman. If your shirt exceeds this measurement, cut it down the side, measure and add one inch to the circumference measurement. Then pin and stitch this side. Press seam open.

You can skip this step if your t shirt already “fits” your ottoman.

Mark top cover fabric 6
Pin side panel for stitching 7Turn side panel inside out and pull over ottoman and adjust so that hem is as even as possible. Then take top piece and place face down on top of ottoman. You should have your inked line facing you. Pin along this line, making sure that t shirt edge is as even as possible with top piece edge. The t fabric tends to roll a bit.

Adjust side panel inside out 8 Pin upside diwn top piece to side panel 9With top piece facing you, carefully stitch along your ink line, keeping under fabric from bunching. Trim excess seam allowance fabric to about 1/2″.

Turn inside out and pull over ottoman. This cover is fairly plain, but imagine the possibilities, and so easy to do!

Casual tshirt slipcover!