You can make these comfy, cozy slipper socks in a single afternoon! The really great thing about this easy knitting project is that it’s calming, gives you a chance to catch up on your favorite listening and results in a great handmade gift for a friend!
Even if you’re unfamiliar with loom knitting, you can do this. I would recommend first viewing this video, which will show you in a few minutes the basic e wrap stitch, which is used on the slipper sock from ankle to toe. https://www.youtube.com/watch?v=7DVRbwzQm7A
Supplies you’ll need:
The loom is a small 24 peg that can be used for baby hats and scarves as well. Have to do a shout out about the knitting counter; I could not do this project without it. http://www.clover-usa.com/en/knitting-and-crochet/80-knitting-counter-mini-kacha-kacha.html?search_query=counter&results=2
A few words about yarn. I doubled the lighter weight green yarn used on the cuffs. It more closely follows the medium bulk of the heel and foot. For the toe I went to a lighter yarn and a single strand. The toe, of course, is cinched up and makes the decrease easier with less bulk. All the yarn shown here is washable wool blend, lovely soft. You can use whatever you like, but I find the 100% acrylics not quite so soft a feel.
Onward to the cuff…
E wrap a single row, referring to above referenced video if you need. For the next 12 rows, you’ll alternate knit and purl stitches in each row. k,p,k,p,k,p etc. If you’ve not done this on a loom, you’ll work to the right with working yarn in front. The first peg to the right of the anchor will be knit. For the knit stitch the hook reaches under the wrapped loop, and grabs the working yarn from above, gets pulled down and knit off. The next stitch is purled, and the process is reversed. The hook will go behind the loop from the top, reaching down to grab the working yarn. Knit and purl alternately for 12 rows. Leaving a tail five inches or so, cut the cuff working yarn and double knot to ankle/foot yarn.
I would be so lost without my little knitting counter friend!
The ankle is simple and quick…just e wrap knit 5 rows. This usually takes me two or three songs to do.
The next thing to do is mark the 13th peg. I’ve used a green wire tie here, and this works fine. Now is the time to leave a yarn tail, cut the cuff yarn, and double knot the heel yarn. For the heel, you’ll only be working pegs 1-12, and will e wrap back and forth between them for 4 rows. Always start on adjacent peg, and do knit the last peg.
To decrease heel and reattach to loom, you’ll leave your (13th peg) marker on and, beginning at the 12th peg, pull that loop onto the adjacent (11th) peg. Go to peg one, wrap (peg 11 as well, even though it will have three loops on it) and work the row, treating the bottom two loops on peg 11 as a single loop. Then go to peg 1, moving it to adjacent peg 2 and following the above instruction until there are three empty pegs per side.
To reattach your knitting to the loom, with your hook take a top edge loop of yarn closest to peg that’s holding the ankle knitting and put on that peg (it will eliminate holes). Same thing for remaining six empty pegs. This part can be a bit of a challenge, but take your time to “see” the best way to spread out the heel knitting over the pegs and it will be fine. Also, if there are any holes in the heel/ankle/foot area, those long tails from changing yarn make stitching the hole shut an easy matter.
Once you’ve got your knitting reattached, cut a long tail and switch back to yarn that was used for the ankle. Double knot, and e wrap all round the loom. You’ll now remove that marker from peg 13, and notice that your number one peg is now on peg 4. There will be three loops on a couple of the pegs, treat the bottom two as if they were a single loop.
From here until the toe, knit as many rows as desired. On a medium bulky yarn, I find 22 rows equates to about a womens 7.5. As you approach the end of the foot, make certain the knitting is not too tight. The toe will consist of three additional rows.
When you reach the toe, cut a tail several inches long and tie on the yarn you’ll use for this. Best to use a yarn about half the thickness of the foot yarn. Double knot, and move every other peg onto the adjacent peg to the right. Then “weave” the working yarn in front of the pegs with loops and behind the empties. Not too tight. Then knit the double loops over. Pulling one peg over at a time is easier than both at once.
Do the next two rows the very same way, remembering to keep yarn loose for ease.
Leave a tail about one and a half times the loom diameter and thread onto your flexible yarn needle. Go through all loops, and once again through first loop. At this point you can remove knitting from loom and turn inside out to close (drawstring) as well as weave in all tails and stitch any holes that may exist. If you’ve not used this drawstring method, here’s an excellent lesson in doing so http://www.loomahat.com/how-to-loom-knit-a-hat/close/ .
The second sock goes much quicker with the insight from the first one. A bow sewn on the cuff from yarn that’s been braided or spool knit https://bettyrockwear.com/retro-craft-tools-spool-knitter/ would really make for a special handmade gift. Or enjoy them on your own feet!